DC Motor Controls and Brushless Motor Controls

Download PDF link

Control selection

DC motor drive selection guide

Suitable motors Type Amps S1 Amps S2
EC008.120 PLN19-8 - PLN20 0.80 1.40
EC008.240 PLN19-8 - PLN20 0.38 0.80
EC016.120 PLN19-8 - PLN20 1.4 2.4
EC016.240 PLN19-8 - PLN20 0.7 1.3
EC020.120 PLN19-8 - PLN20 3.2 4
EC020.24E PLN19-8 - PLN20 1.5 2
EC030.240 / 24E PLN19-8 - PLN20 2 3.5
EC035.120 PLN20 5.2 8
EC035.240 PLN19-8 - PLN20 2.6 4
EC050.12E PLN20 6.8 9.4
EC050.24E PLN19-8 - PLN20 3.4 4.7
EC070.12E PLN20 8.4 11.8
EC070.24E PLN19-8 - PLN20 4.2 5.9
EC100.120 PLN20 12 16.8
EC100.240 / 24E PLN20 6 8.4
EC180.120 PLN40 21.5 30
EC180.240 / 24E PLN20 10.8 15

Brushless motor drive selection guide

Suitable motors Type Amp non Amps picco
BL002.240 BLD07-IT 1 2
BL005.240 BLD07-IT 1 3
BL012.240 BLD07-IT- BLD15 3.5 7
BL018.240 BLD07-IT- BLD15 5 10
BL025.24E BLD07-IT- BLD15 7 14
BL032.240 BLD07-IT- BLD15 5 10
BL043.240 BLD07-IT- BLD15 6 12
BL070.48E BLD15 10 20

DC motors controls

EC050

PLN19-8

 

SINGLE DIRECTION PWM CONTROL FOR DC MOTORS

Line voltage at terminals FA1 and FA2:
12 – 24 Vac or 15 – 35 Vdc

● The speed of the drive is to be controlled by potentiometer, 10K Ω

● Current Limit trimmer, in order to suit the board for small motors. In order to limit the current, turn clock wise the trimmer.

● Output voltage from terminals FA3 and FA4, from 0 up to Vdc
MAX which is proportional to the input voltage. With 35 Vdc
input voltage, the max output voltage is about 30 Vdc.

● Output current (NOTE1):

● Maximum output current allowed: 8 A in a ventilated environment, continuous duty

● Weight: 120 g.

EC050

PLN20/40

 

LOW VOLTAGE BIDIRECTIONAL PWM DC MOTORS CONTROL

● Following settings can be adjusted (by built in trimmers):
– acceleration ramp: 0.5 – 10 sec
– deceleration ramp: 0.5 – 10 sec
– current limit 100% – about 30%

● TRoom temperature: 0°C / +40°C (alarm below zero)

● LED for system diagnosis

● Switching frequency: 16kHz

● Covered

● 5-10 kΩ Speed pot. or 0-10 Vdc external signal for speed regulation 0-10 Vcc

● Variable current limit

● Thermal sensor for protection

SalvaSalva

Brushless motors controls

BLD07

BLD07-IT

 

Brushless motors bidirectional control

The BLD07-IT drive is the new and updated version of the previous BLD07. Built on a new PCB, features and functionality have been implemented, where previously could only be achieved with higher power drive. The result is to have a more versatile drive and to 'cutting edge, which can be customized, or controlled via the field bus (CAN Open optional).

L'azionamento BLD10

BLD15

Link al download del PDF   download-manual
 

BLD10 drive for brushless motors

Standard features:

● Low voltage power supply 24/36/48 Vdc
● Protection IP54
● Motor torque ratings available from 0.22 up to 2.1 Nm
● Die-cast aluminium housings
● Permanent synthetic oil long life lubrication
● Gearbox only version also available, with either standard input flange or customized flange and coupling

SalvaSalva